To send me a mail, please click HERE ! As payment, we accept wired bank transfer, and PayPal
No credit cards, sorry, but you may use them with
PayPal accepted, but all payments MUST to be received NET from the 4% fee, sorry
ATTENTION: ready cases (many are ready !) are usually sent within 2/3 days.
BUT, not ready cases and other items may need a CALM 15+ days making time !
------------------------------------------------------------------------------------------------------------------------------------------------
ATTENTION: I reserve the right to improve my cases, as actually I am doing very often !
Then, some of the recently made cases may slightly differ (in better) from the pictured ones !
---------------------------------------------------------------------------------------------------------------------------------------------
ATTENTION: I reserve the right to improve my cases, as actually I am doing very often !
Then, some of the recently made cases may slightly differ (in better) from the pictured ones !
--------------------------------------------------------------------------------------------------------------------
MY ONLY shipping address, for items or payments:
Luigi Crescenzi, via Courmayeur 35, 00135 Roma, Italy
in order to convert EURO in your courrency, please click: http://www.xe.com/ucc/
ONLY for emergencies, please, call me at ++39 337 747633
In fact, I definitely PREFER to communicate by email, it's a lot better for both !
Dear visitors of this page(s), let me finally introduce "officially" my very special Tripod "flush" SCREW, the one that some (few) buyers of my cases already knows... Sincerily, I am quite proud of this my idea ! Unlike Leica cases screws, and, as far as I know, unlike ALL cases screws, this special "Luigi's" screw still leaves the case bottom perfectly flat, without the uncomfortable protrusion on the bottom, that prevents the case (and the camera) to rest firmly even on the most flat surfaces ! His design permit to easily operate it with any thin coins, and in the lower part there is the useful TRIPOD hole, with the smaller thread, the one actually used by ALL makers.
A picture showing my "Aged Brown" added patina... Euro 10 extra, sorry.
It is quite costly, Euro 60 each (fitted), because: 1. every screw is hand made with a lathe - 2. the screw is all made in solid stainless steel, of which I am a fanatic user, being me a "boat's man"... - 3. to fit well it is a not easy job, it takes a lot of time and care, and there is always the risk to ruine a NEW case !
ATTENTION: the "Bottom SCREW" is not fitted in our cases by default !
It will be fitted ONLY upon a clear request, and a related payment for it.
ATTENTION: for my "how to purchase" INFO page, please click HERE !
Original Luigi's, cases for Epson R-D1
Cases Solutions since the year 1998 !
(click) - For our colours samples...
Do you bought an Epson R-D1 ? Well, here SIX my cases for it !
Here the version without my built-in-grip, aged brown (left, + Euro 10) and cognac brown (right)
Euro 170 (no strap) with rear flap,that may be hanging, or fully detacheable - Strap, Euro 60
(click) - For our colours samples...
ATTENTION ! I am always improving my cases !
Looking attentively at those pictures, you will see that
the actual rear cutout is now a better designed one, with
a single, well, properly shaped hole. I make it since two years !
And, now, you may have: NO flap, Hanging flap, Detacheable flap !
Here my latest case model for it... An half case, with the useful built-in-grip !
It is usually ready for shipping in black or brown finish. Other coulours, upon request
Only the half case, with built-in-grip, and rear "patch", Euro 200 - Deluxe strap, Euro 60
OR... for whom like to save, here my NEW "Basic Line" cases...
Very fine quality despite different leathers, NOT hand stitched, made in two
models, each one in the FOUR shown finishes:
- Standard Basic half case, hanging flap, small "bump" on front, Euro 90
- Built-in-grip Basic half case, with a whooden (leather lined) grip, Euro 110
Very fine quality despite different leathers, NOT hand stitched, made in two
models, each one in the FOUR shown finishes:
- Standard Basic half case, hanging flap, small "bump" on front, Euro 90
- Built-in-grip Basic half case, wist a wooden (leather lined) grip, Euro 110
(Page under construction, cases are ready for shipping !)
Here the machined, less costly half case that I designed for Leica M cameras, and that since today
(January the 16th, 2006) I am offering also for the LONE Digital RF, Epson R-D1 ! All of them are made
WITH the rear cutouts, and the recently introduced removable rear "door" ! With deluxe strap, Euro 170
Please note that we are offering the strap, along with THIS case model, at a very low amount ! Take it !
Here our LESS COSTLY half case for Epson R-D1, shown in 11 different colours !
LESS COSTLY half case for Epson R-D1, Euro 170 with DELUXE STRAP
Note: this case is already provided with the recently introduced "rear door + patch" !
Ready for shipping my "normal" half case for your valuable Epson R-D1
I want to express my thanks to the kind customer that then me
the two 1st pictures below, that I like more than mines !
I can make the LCD screen rear cutout, BUT I like to make it upon a clear
buyer's request, in the same rectangular size, and shape. NOW, I solved
the problem of the LCD screen protection, thanks to a removable patch !
Euro 180, + Euro 60 if the OPTIONAL strap is required, too, plus
Euro 25 Fedex shipping, or Euro 16 for Registered Air Mail.
The ordered R-D1 cases will be shipped immediately, I have them in stock, now !
Look how smart is this half case made in genuine green CROCO !
It comes with a croco and green calf special strap, the PERFECT GIFT, Euro 390
Now, also a FULL case for your R-D1 has been made !
Please, read, and look at the many pictures...
Prices: Full case Euro 320, optional strap Euro 60, cards holder (2 places) Euro 10
LOOK ALSO AT THE NEW PROPOSAL BELOW ! :-)
(
)
